The short answer: ASTM F963-23 is the current mandatory US toy safety standard, effective 20 April 2024 under 16 CFR Part 1250. Test reports and Children's Product Certificates (CPC) based on F963-17 are no longer accepted by the CPSC after that date. If you are placing an order now, the lab report must cite F963-23.
The ASTM F963 version timeline
Buyers often search for "F963-11 vs F963-16" because those are the versions printed on older quotes. Both are long superseded. The table below is the sequence that matters when you check a supplier's paperwork.
| Version | Status | Mandatory from | What it means for a buyer today |
|---|---|---|---|
| F963-11 | Superseded | 12 June 2012 | First version incorporated as mandatory after CPSIA; replaced F963-08. Reports citing it are obsolete. |
| F963-16 | Superseded | 30 April 2017 | Published October 2016. Common on quotes from 2017–2018, but no longer acceptable for a new CPC. |
| F963-17 | Superseded | 28 February 2018 | Adopted by CPSC direct final rule (4 Dec 2017). Reports based on it stopped being accepted on 20 April 2024 — this is the one that still catches buyers out. |
| F963-23 · CURRENT | Mandatory | 20 April 2024 | Published 13 Oct 2023, incorporated by CPSC direct final rule (18 Jan 2024). The only version a new US test report and CPC should cite. |
A practical rule: when a factory hands you a test report, look at the standard version on the first page, not just the word "pass". A passing F963-17 report is not a passing US compliance file in 2026.
What actually changed in F963-23
The 2023 revision is not a paperwork update. Six changes affect how a plush, vinyl, ABS or resin toy is designed and specced:
- Heavy elements in substrates. Exemptions for paper, textiles and modelling clay are described separately and more strictly. A fabric covering is no longer an automatic exemption for the substrate underneath — relevant for plush with plastic eyes, noses and internal parts.
- Phthalates widened from 6 to 8. Now aligned with 16 CFR Part 1307: DEHP, DBP, BBP, DINP, DIBP, DPENP, DHEXP and DCHP, each below 0.1%, for all children's toys. Previously DEHP at 3% was limited to pacifiers and rattles.
- Battery accessibility. Higher requirements for battery compartments (a tool or two independent movements to open), new abuse tests for lithium-ion cells, and associated instruction and warning labels.
- Magnetic toys. A 24-hour flux decay test in addition to the 50 kG²/mm² flux index, plus a stricter accessibility probe — catches magnets that pass once then degrade.
- Sound and expanding materials. Close-to-the-ear peak limits and new impulse-noise limits; expanded scope for water-absorbing expanding materials.
- Traceability labelling and projectile toys. New sourcing-label requirements and re-sequenced projectile clauses with kinetic energy limits.
Toy pigments, coatings & heavy-element limits
This is where most custom-toy failures originate. Painted eyes, printed fabric, soft PVC parts and coloured resin all carry pigments and film-forming solids that are tested as a dry coating. Section 4.3.5 of ASTM F963 sets these maximum soluble migrated element limits (ppm, mg/kg):
| Element | Solubility limit | Where it typically shows up |
|---|---|---|
| Antimony (Sb) | 60 ppm | Pigments, flame retardants in textiles |
| Arsenic (As) | 25 ppm | Contaminated mineral pigments |
| Barium (Ba) | 1000 ppm | Fillers, printed plush fabric, granular stuffing |
| Cadmium (Cd) | 75 ppm | Bright yellow/red pigments, stabilised PVC |
| Chromium (Cr) | 60 ppm | Chrome-based colourants, metal plating |
| Lead (Pb) | 90 ppm | Paint, ink, pigments, soldered or plated parts |
| Mercury (Hg) | 60 ppm | Contaminated raw pigment batches |
| Selenium (Se) | 500 ppm | Cadmium-selenide red/orange pigments |
On top of the soluble-element table, two total lead ceilings apply: 90 ppm in surface coatings (16 CFR 1303) and 100 ppm in accessible substrates (CPSIA). These are separate tests — a pigment can pass one and fail the other.
For the EU the equivalent is EN71-3, which covers 19 elements with a different sample preparation and different limits. The two reports are not interchangeable. A toy sold into both markets needs both, which is why we spec materials to the stricter of the two from the first sketch.
A compliance checklist you can send your factory
Copy this into your RFQ before tooling starts. Each item is cheaper to fix on paper than after a mould is cut.
- Confirm the destination market and require the lab report to cite ASTM F963-23 (US) or the current EN71 series (EU/UK), as applicable.
- Ask the pigment / masterbatch / ink supplier for a heavy-metal test report covering all eight soluble elements, plus total lead for both coating and substrate.
- Require phthalate-free (8P, each <0.1%) declarations for every plasticised PVC, soft vinyl and flexible component.
- Specify eye and nose attachment by pull/torque test method, not by glue type — small-part failure is still the top recall cause.
- If the toy has batteries, magnets or sound modules, flag them at design stage; all three gained new tests in F963-23.
- Book the CPSC-accepted lab slot when the golden sample ships, not after it passes internally.
- Have the importer issue the CPC from that report; keep reports and certificates on file for at least five years.
This page is a plain-language buyer guide, not legal advice. Standards and CPSC rulemaking change; always confirm the current mandatory version and your importer's documentation requirements with a CPSC-accepted laboratory before production.